fedora core 6

Macross · Post by **Macross** » 02 May 2007, 11:18

So i have a problem connecting to the internet.Here is my usb modem http://eciadsl.flashtux.org/modems.php?modem=65 I have followed EciAdsl installation guide and it still didnt work for me.Any suggestions how could i make it work?

(sorry for my bad english)

Post by **computathug** » 02 May 2007, 11:41

have you gone through your router settings?

in your browser type in 192.168.1.? depending on manufacturer the last digit or digits may vary

then most routers run a connection wizard. hope this helps

Post by **bad_brain** » 03 May 2007, 04:31

impossible to say without more info....is the router working and you just can't go online or can't you access the router at all (ping it)?

Macross · Post by **Macross** » 03 May 2007, 05:06

Edited: At first i couldn't access modem

finally made it work with my modem but now it dosent connect to the internet it says "modem hangup" What does that mean?

Post by **bad_brain** » 03 May 2007, 05:34

hm, most likely either wrong internet access data or the ISP or wrong interface setup. make sure the ISP data is correct, when it still not works post the output you get from the ifconfig command.

Macross · Post by **Macross** » 03 May 2007, 09:30

ifconfig:

link encap:Local loopback
inet6 addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope: Host
up LOOPBACK RUNNING MTU:16436 Metric:1
Rx packets:1471 errors:0 dropped:0 overruns:0 frame:0
Tx packets:1471 errors:0 dropped:0 overruns:0 colisions:0 txqueuelen:0
Rx bytes:2323064 (2.2Mib) tx bytes:2323064 (2.2Mib)

Macross · Post by **Macross** » 04 May 2007, 04:22

Bump

Waiting for replay.

Post by **bad_brain** » 04 May 2007, 04:52

sorry, I'm sick at the moment so replies take a little longer than usual.
hm, seems the connection data is wrong, have you re-entered the ISP data?

Post by **pseudo_opcode** » 04 May 2007, 07:41

bad_brain wrote:sorry, I'm sick at the moment so replies take a little longer than usual.
hm, seems the connection data is wrong, have you re-entered the ISP data?

OMG b_b you're sick?? God bless ya..
Get well real soon

@Macross
U only have fedora core 6 or is it dual boot.. if yes, can you access internet in windows?
Is your ISP a DHCP one or does it provide static ip(internal)??
When you ping any site what error do you get? cannot resolve hostname???

try

Code: Select all

ifconfig eth0

Post by **bad_brain** » 05 May 2007, 04:46

already feeling a little better...

well, the problem is that I don't know if eth0 is used at all in this case because it's an USB connection...should be sda1 then. best try to setup sda1 as network device first and if it don't work try eth0:

Code: Select all

route add default gw IP.of.your.router sda1
ifconfig sda1 up

or

Code: Select all

route add default gw IP.of.your.router eth0
ifconfig eth0 up

Macross · Post by **Macross** » 05 May 2007, 04:58

Ok i will try.

Post by **pseudo_opcode** » 05 May 2007, 08:09

oh lol.. i didnt know its usb..

Macross · Post by **Macross** » 05 May 2007, 13:47

here what i get when i try to connect

root@localhost ~]# eciadsl-start
[EciAdsl 1/5] Setting up USB support...
Preliminary USB device filesystem is OK
[EciAdsl 2/5] Uploading firmware...
Process skipped .. no more needed
firmware loaded successfully
[EciAdsl 3/5] Synchronization...
OK eciadsl-synch: success
Synchronization successful
[EciAdsl 4/5] Connecting to provider...
using channel 14
Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
Script /usr/local/bin/eciadsl-pppoeci -vpi 8 -vci 35 -vendor 0x0915 -product 0x8102 -mode LLC_RFC2364 finished (pid 31959), status = 0x0
Modem hangup
Connection terminated.

Tryed

Code: Select all

route add default gw IP.of.your.router eth0 
ifconfig eth0 up

it says that connection is unreachable.

When i type eciadsl-testconnection command it says the same.

Post by **bad_brain** » 06 May 2007, 05:47

hmmm...everything seems to work fine until the actual connection to the ISP is made...are you REALLY sure the ISP connection data is correct? best enter it again, just to make sure....

if you have a firewall best turn it completely off for a test.

Macross · Post by **Macross** » 06 May 2007, 06:21

well i turned off firewall and still same.Im not sure what numebrs should be entered here

USB ALT INTERFACE for PPPOECI process currently set to 4
Type in the USB ALT INTERFACE for PPPOECI (1-digit decimal (0-5) , press ENTER to keep current value):

and what settings should be here:

1) Previous setting (LLC_RFC2364)
2) VCM_RFC2364
3) LLC_RFC2364
4) LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS
5) VCM_RFC_1483_BRIDGED_ETH
6) LLC_RFC1483_ROUTED_IP
7) VCM_RFC1483_ROUTED_IP

Enter your choice (1-7, default is 1):

maybe i entered incorect something here.